“The foundation of your home is built up by the walls. The weather out there will not be nice and you need to pay special attention to the exterior walls of your house. Painting your wall isn’t enough to make it waterproof. After dealing with rain, snow, wind, dust and heat of the outside environment, the paint will start peeling off.”

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

“The outer part of your home’s wall is usually covered with a lot of dust and dirt from the air. To ensure the efficiency of the entire process, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned with a broom, brush, or sandpaper. Then rinse it off with a power washer.”

Step 3: Check out for the cracks and fill them up

“Cracks and holes can be found over time on your walls. Follow up the cleaning process with a thorough look at the cracks and holes on your wall to make sure it’s waterproof. Then fill them with the cement.”

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

The cement mixture seals the cracks. Make sure to remove the loose cement from the wall before applying the cement.

Step 4: Add a layer of cement waterproofing sealer

If you want to make sure your wall is waterproof, you need to apply the cement waterproofener. After applying the cement in the crevices, let it dry and then apply the waterproof paint sealer. Allow it to become dry after that.

Step 5: Pick the right water-proofer

There are a lot of products in the market that are waterproof. You need to pick the right one for your wall. The water-proofer should be chosen based on whether the wall is concrete or silicate.

You can choose between a silicate-based concrete sealer and a concrete coating. Pick a plaster waterproof Additive that will add strength to your walls

Step 6: Apply the water-proofer

The water-proofer should be applied with a roller or brush. If you want to apply more than one coat, give a thin coat first. Let the first coat dry before adding the second.

Step 7: Apply tar and heavy-duty membrane

If you want to add more strength to the layers, you need to use a tar-based pitch. It should be applied on your wall.

If you want to waterproof your walls, you need to apply a heavy-duty plastic or rubber membrane after that.

Step 8: Consider adding gravel

To lay the drainage pipes, you need a base below the footer. The drainage pipes will get adequate support from a gravel base. Gravel is long-lasting and provides enhanced protection.

You need to lay the drainage pipe-cover with the gravel. The gravel should be level near the footer. A covering for the pipe should be at least 3 inches.

Step 9: Add a fabric barrier

Attach the fabric barrier to the pipe. Ensuring a fabric barrier is going to keep your system clean. Then build the top of the dirt relatively high and allow it to settle for a while. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia

Conclusion:

Your home will have a new life if it is waterproof. Magicrete can help you with waterproof solutions for your walls. At a very low and affordable price, Magicrete can help you with your outdoor needs.

“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like”